Cement Testing Equipment

Approx. Rs 60,000 / PieceGet Latest Price

General Description & Specification:
Accelerated Curing Tank having capacity to accommodate 6/12/18 Concrete Cubes of 150mm size with a facility for accelerated curing by Boiling water method up to temperature range : 100 +/- 2 deg.C as per IS standard IS : 9013. Also it will have capacity for curing by warm water method at temperature 55 +/- 2 deg.C
Tank will consist of a rectangular double walled metal cabinet, inside lined with stainless steel, outer powder coated. Easily replaceable high Wattage heaters are mounted in side the chamber. A slow speed stirrer is provided to circulate water inside the chamber to maintain the uniform temperature of water. A strong stainless steel perforated platform is provided for keeping the cubes and also have a lid with lifting handle to cover the chamber.
The temperature is indicated and controlled by a DIGITAL auto tuning PID Temp. Controller with soak timer to control the duration of heating and then to shut down the system without manual attendance. The front panel will have power supply indicating lamp, control action indication lamp and one main switch. Suitable for operation on 220 V, 50 Hz single phase, AC supply or 440 V 50 Hz, three phase AC supply, for bigger size of curing tank.

Optional Accessories
Rubber hand Gloves. Spare Heaters. Low water Level cut off device to safeguard heaters against low water level burn out In built refrigeration system for curing at 27 deg C

Recommended Accessories & Consumbles
The following accessories and consumables are not part of the standard supply and are mandatory for the testing work

Also Available
Accelerated Curing Autoclave : By Steam Pressure
Accelerated Curing Drier : By Dry Heat

Optional Accessories:

• Rubber hand gloves.
• Spare heaters.
• Low water Level cut off device to safeguard heaters against low water level burn out.
• In built refrigeration system for curing at 27 deg C

SIZE PRISE
1- 3 CUBE MOULD 24000
2- 6 CUBE MOULD 36000
3- 9 CUBE MOULD 45000
4--12 CUBE MOULD 70000
5 -18CUBE MOULD 90000
6 -24 CUBE MOULD 105000
7- 36 CUBE MOULD 150000

Approx. Rs 70,000 / NumberGet Latest Price

• Double walled, inside chamber stainless steel, outer body made of CRC/G.I. – powder coated.
• Temperature ranges from 10°C to 60°C controlled by Dual display microprocessor based Digital temperature indicator cum controller with ± 0.5°C accuracy or better.
• Cooling system consist of high efficiency Kirloskar Make compressor with relevant accessories.
• Humidity ranges from atmospheric humidity to 95 % controlled by dual display Microprocessor based Digital Temperature Controller (Dry and Wet bulb method) with accuracy +3 % RH or better
• Inner water tank made of stainless steel with ball cock valve
• Front door has a full view glass observation window

Additional Information:

Approx. Rs 25,000 / NumberGet Latest Price

CONSTANT  TEMPERATURE BATH :
PLY SAMPLE SIZE : 12"X12"
BATH WORKING SIZE : 14”X 10”X 14"

Additional Information:

Approx. Rs 500 / NumberGet Latest Price

Additional Information:

Approx. Rs 60,000 / NumberGet Latest Price

General Description & Specification:
Accelerated Curing Tank having capacity to accommodate 6/12/18 Concrete Cubes of 150mm size with a facility for accelerated curing by Boiling water method up to temperature range : 100 +/- 2 deg.C as per IS standard IS : 9013. Also it will have capacity for curing by warm water method at temperature 55 +/- 2 deg.C
Tank will consist of a rectangular double walled metal cabinet, inside lined with stainless steel, outer powder coated. Easily replaceable high Wattage heaters are mounted in side the chamber. A slow speed stirrer is provided to circulate water inside the chamber to maintain the uniform temperature of water. A strong stainless steel perforated platform is provided for keeping the cubes and also have a lid with lifting handle to cover the chamber.
The temperature is indicated and controlled by a DIGITAL auto tuning PID Temp. Controller with soak timer to control the duration of heating and then to shut down the system without manual attendance. The front panel will have power supply indicating lamp, control action indication lamp and one main switch. Suitable for operation on 220 V, 50 Hz single phase, AC supply or 440 V 50 Hz, three phase AC supply, for bigger size of curing tank.

Optional Accessories
Rubber hand Gloves. Spare Heaters. Low water Level cut off device to safeguard heaters against low water level burn out In built refrigeration system for curing at 27 deg C

Recommended Accessories & Consumbles
The following accessories and consumables are not part of the standard supply and are mandatory for the testing work

Also Available
Accelerated Curing Autoclave : By Steam Pressure
Accelerated Curing Drier : By Dry Heat

Optional Accessories:

• Rubber hand gloves.
• Spare heaters.
• Low water Level cut off device to safeguard heaters against low water level burn out.
• In built refrigeration system for curing at 27 deg C

SIZE -------------- PRISE
1- 3 CUBE MOULD--24000
2- 6 CUBE MOULD---36000
3- 9 CUBE MOULD---45000
4--12 CUBE MOULD--70000
5 -18CUBE MOULD---90000
6 -24 CUBE MOULD---105000
7- 36 CUBE MOULD-- 150000

Additional Information:

Approx. Rs 9,500 / NumberGet Latest Price

Approx. Rs 85,000 / NumberGet Latest Price

Approx. Rs 600 / NumberGet Latest Price

Additional Information:

Approx. Rs 40 / PieceGet Latest Price

Approx. Rs 15,000 / NumberGet Latest Price

Additional Information:

Approx. Rs 30,000 / NumberGet Latest Price

The machine embodies an hydraulic system designed to meet the requirements of Indian standards Specification 516-1959 for compression tests on cement mortar cubes up to 7.06 cms.

Loading Unit
The hydraulic jack of 500 KN capacity is fixed to the base. The upper platen has got a self aligning action and is attached to a screw which passes through the cross head plate, and can be raised or lowered for initial clearance adjustment. The lower platen rests on the jack ram and is positioned with the help of a centring pin. Loading is accomplished by upward movement of lower platen. A dust cover is provided on the jack to prevent any dust from going into the cylinder. A spacer with a centering locating pin is provided to test small specimens. The lower and upper platens of the machine are hardened ground and polished. Guidelines are marked on the lower platen to keep the specimen coaxial with the hydraulic jack.

Pumping Unit
The motorised pumping unit which is housed in an elegant console is of double plunger type and is driven by three phase 440 volts 50 cycles electric motor. The pumping unit is a seperate unit connected to the jack by means of a steel connecting tube. A junction box is suitably fixed to connect the motor to the mains through a push button starter. The pumping unit is fitted with a 20cm dia, dial hydraulic pressure gauge with 250 division i.e. 0-500 KN X 2 KN. A max red pointer is provided to facilitate taking readings after failure of the specimen. The pressure gauge is fixed at an Angle for easy readability. The machine is fitted with hand wheel control which enables the rate of application of load to varied. The machine is equipped with the facility of Hand Pumping in case of power failure. The electric pumping unit is fixed with a micro-switch to switch off the motor automatically as the load on the machine approaches the rated capacity. Relays are incorporated in the pumping unit so that in case of break down of power supply, the motor will stop and would not re start unless the starting switch is operated. Complete with our own calibration certificate for pressure gauge with National Traceability.

Standard Accessories

• The Machine can be supplied with NCCBM Calibration certificate at an extra cost.
• The Machine can also be supplied with 2 or 3 pressure Gauges of 100 KN, 250 KN and 500 KN for testing lower strength cubes or smaller size cubes.

Approx. Rs 6,500 / NUMBERGet Latest Price

The fineness of cement has a significant effect in its physical properties when used in concrete. Generally the finer the cement powder, the more rapid the concrete will set, as there is an increase in its surface area. The measure of fineness is usually undertaken by sieving, and the result assessed against the cement standard for compliance. The Blaine air permeability apparatus is used to determine the fineness of Portland cement in terms of the specific surface expressed as total surface area in square centimeters per gram of cement. The Blaine apparatus draws a defined volume of air through a prepared bed of cement of defined porosity.

General Description & Specification:
The apparatus comprises one each of Brass or stainless steel permeability cell 12.5mm,’U’ tube manometer with stop cock mounted on a laminated wooden stand, perforated metal disc, plunger, Rubber stopper, Rubber tube – 30cm long with rubber bulb.

Optional Accessories

At extra cost

• Balance with 0.001 gm resolution
• Stop Watch with 0.5 second resolution
• Manometer Liquid
• Whatman Filter Paper
• Filter Punch

Additional Information:

Approx. Rs 28,000 / PieceGet Latest Price

The consistency and workability of concrete is a very important factor and is strictly connected to the water/cement ratio, to the effect of admixtures and finally to the strength and quality of concrete. Suitable for concrete mixes of high and very high workability. To perform this test, a sample is placed on a metal surface which is then raised and dropped through a known height.

General Description And Specification

As per IS : 5512 for cement Mortar and Lime
The flow table consists of a brass table top 250 + 2.5mm dia mounted on a rigid stand. The table top is reinforced with equally disposed ribs and allowed to drop through 12mm by a ground and hardened cam, Complete with mould 100mm base dia, 70mm top dia and 50mm high. The cam shaft is rotated at the rate of 100 RPM by an electric motor. Suitable for operation on 230 Volts 50 cycles. Single Phase, A.C. Supply. Manually operated flow table also available.

Optional Accessories

As per Is : 199 for concrete
The Flow Table consists of a brass or Mild steel table top of 76.2 cms(30″)dia, finely machine from a solid brass casting or Mild steel Plate. The stand is fabricated out of cast iron/mild steel and is of study construction. The ground and hardened steel cam is designed to drop the table by 12.5mm. Complete with flow mould with handles with one tamping rod 0-60 cms long X 16cm. electrically operated to raise and drop the table top. approx. 15 times in 15 seconds. Suitable for operation on 230 volts, 50 cycles, A.C. Supply. Manually operated flow table also available.

Approx. Rs 55,000 / UnitGet Latest Price

Silent Features:

• Rust proof stainless steel pressure vessel
• Specially designed Steam Safety Valve, pressure control switch and Temp. control switch – Triple Safety precautions for operator safety
• Accurately Calibrated Pressure Gauge
• Guaranteed timings and performance as per IS 4031

General Descripation & Specifications:
The Autoclave is double walled. Inner boiler chamber of stainless steel cylinder, with concealed yet easily replaceable heaters surrounding the vessel for quick heating. The boiler lid is of thick stainless steel and can be bolted to the chamber by heavy hexagonal nuts. The silicon gasket, seated in a groove, makes the unit leak proof even at high pressure. The boiler is mounted in between the strong angle iron frame and covered with CRC sheet – attractively powder coated. The outer cover can also be of Stainless steel at an extra cost. The gap in between the walls is filled with thermal insulation to prevent heat loss and energy. The control system consist of sensitive pressure regulator, pressure gauge, safety valve, temperature control switch, power ON-OFF switch and pilot lights to indicate status of the electric heating units and control switches.

Standard Accessories:

• Special rack to hold specimens above water level in the autoclave and in vertical position
• Pressure gauge with calibration report with national traceability
• Silicon rubber Gasket
• Spanner

Accessories At Extra Cost:

• Length comparator with dial micrometer 0.002mm X 5mm
• shrinkage bar moulds(single/two/triple gang)
• PID Auto tuning Digital Temp. indicator cum controller with or without PC interface for data logging
• PID Auto tuning Digital Pressure indicator cum controller with or without PC interface for data logging
• Spare heater set
• Spare Silicon Gasket
• Spare Pressure gauge
• Spare safety valve

Approx. Rs 56,000 / UnitGet Latest Price

Approx. Rs 12,500 / NumberGet Latest Price

Additional Information:

Approx. Rs 2,000 / NumberGet Latest Price

• Consist of a metallic frame bearing a movable rod with cap at one end. The needles and plunger can be fixed centrally in to the rod by clamping screw. The movable rod carries an indicator which moves over a graduated scale attached to the frame. The scale is 40mm in length with the smallest division of 1mm. The dashpot facilitates the gentle lowering of the movable rod with needle.
• The vicat moulds can be in the form of frustum of a cone having 70 mm in dia at the base, 60 mm at the top and 40 mm high or split type. A non porous base plate of glass or metal also provided. Complete with consistency plunger, initial and final setting needles in a nice jewellery case.
• Type: Vicat Needle Apparatus

Approx. Rs 2,000 / NumberGet Latest Price

The main purpose of the soundness test is to assess the possible risk of late expansion due to hydration of uncombined calcium oxide and/or magnesium oxide. The test uses apparatus known as Le Chatlier apparatus, which magnifies any expansion during heating to a value that can be measured.

The apparatus consist of a small split cylinder of spring brass or other non-corrodible metal of 0.5 mm thickness forming a mould 30 mm internal diameter and 30 mm high. On either side of the split, two indicators are brazed suitably with pointed ends made of 2 mm diameter brass wire in such a way that the distance of these ends to the centre of the cylinder is 165 mm. The split cylinder will be kept between two glass plates.

Approx. Rs 85,000 / NumberGet Latest Price

SPECIFICATION :

cIntroduction

Designed for mixing small quantities of concrete used in preparation of concrete cubes for testing in Laboratories. The purpose of the mixer is to smear mechanically the aggregate surface with cement paste unilormly and produce a mix of uniform consistency. This in turn gives consistent quality of cube specimens when casted in the moulds.

Salient Features :

· Portable & compact.

· Adjustable Blades.

· Simple to clean and maintain.

General Description and Specification :

The concrete mixer developed in transportable on wheels. The design of the mixing developed is ensure uniform and efficient mixing of cement and aggregate in dry & wet conditions. The design also facilitates lifting oi mixing drum with the help of steering wheel. The arrangement helps the operator to access the pan contents conveniently and emptying the mixture after completion of the operation. The drum is driven through a Heavy Duty Gear Box. Positive rotating motion to the drum is ensured by unique design of the ribbed base. The lid with mixing paddles clears off the top of the drum to provide maximum access to the operator.

Optional Accessories : Wheel Barrow, Mixing Pan, concrete Scoop.

Product Specification

Approx. Rs 65,000 / UnitGet Latest Price