Concrete Testing Equipment

Approx. Rs 750 / PieceGet Latest Price

• Complete with base plate. The faces of the mould are machined flat to +/- 0.02mm accuracy and finished to within +/- 0.2mm of specified dimensions. Material for construction of moulds is Cast Iron or Mild steel. The moulds are stout enough to prevent distortion and facilitate the removal of the moulded specimen without damage. The Moulds are so machined that when they are assembled ready for use, the dimensions and internal faces are accurate within the specified limits. Internal faces of the moulds are smooth. The base plate is attached to the mould by cleats .The parts of the mould, when assembled, are positively and rigidly held together during filling, subsequent handling and vibration where applicable.

• As per IS : 10086-1982, The cube mould is so constructed so as to facilitate separation into two parts. The mass of the mould together with the base plate will be 2.8 +/- 0.2 kg. Material for construction of these moulds is mild steel.

• Spanner For Demoulding And Moulding,
• Tamping Rod With Sauqre Face.
  

• For casting concrete specimens for flexural tests. The mould is made of 4 plates assembled together. Each mould with base plate, made of Mild Steel. Faced are machined flat to +/-0.2mm and finished in size to 0.2mm. AS PER IS: 516

Additional Information:

Approx. Rs 2,400 / UnitGet Latest Price

Approx. Rs 1,300 / NumberGet Latest Price

• The apparatus comprise of a slump cone with handles made of mild steel sheet, a chrome plated steel tamping rod of 16 mm diameter X 600 mm long, rounded off at one end, with a scale marked on it and a steel base plate with a carrying handle.
• The mould for the test specimen will be in the form of frustum of a cone having the following internal dimensions as follows.

• Concrete scoop.
• Funnel for pouring concrete in cone straight edge
  

Approx. Rs 4.5 Lakh / PieceGet Latest Price

Approx. Rs 40,000 / NumberGet Latest Price

• The Vibrating table is entirely constructed of thick steel. The table top is made of thick mild steel plate and has stops along its edges to prevent moulds from walking off the table during operation. A cross arm adjustable on a vertical rod at the centre of the table is provided to hold the moulds while operating the table. The variable pitch pulley arrangement permits the variation of frequency between maximum of 3600 vibrations down to 2600 vibrations per minute. A speed regulation handle is provided for increasing or decreasing the frequency. The vibrator is mounted on cushioned steel vibrating deck. A switch is provided for starting the motor.

• 50 X 50 CMS
• 60 x 60 CMS
• 75 x 75 CMS
• 100 x 100 CMS

Additional Information:

Approx. Rs 1.7 Lakh / UnitGet Latest Price

• Calibrating Anvil

Approx. Rs 20,000 / NumberGet Latest Price

• The apparatus, consist of a rigid frame that supports two conical hoppers vertically aligned above each other and mounted above a cylinder. The top hopper is slightly larger than the bottom hopper, while the cylinder is smaller in volume than both hoppers. To perform the test, the top hopper is filled with concrete but not compacted. The door on the bottom of the top hopper is opened and the concrete is allowed to drop into the lower hopper. Once all of the concrete has fallen from the top hopper, the door on the lower hopper is opened to allow the concrete to fall to the bottom cylinder. The excess concrete is carefully struck off the top of the cylinder and the mass of the concrete in the cylinder is recorded. This mass is compared to the mass of fully compacted concrete in the same cylinder achieved with hand rodding or vibration.

• Concrete Scoop
• Straight Edge
• Weighing Balance

Additional Information:

Approx. Rs 15,000 / NumberGet Latest Price

• The apparatus consists of a pressure tight flanged cylindrical measuring bowl of specified volume in accordance with size of aggregate to be tested. The bowl is fitted with a removable flanged conical cover assembly with the help of a airtight sealing gasket. The conical cover has an air valve and a pet cock for bleeding off the water. A transparent cylindrical stand pipe, which is graduated in air content, is fixed to the conical cover assembly. Pressure is applied to the specimen with the help of pressure bulb and the pressure is recorded on the pressure gauge which is mounted on the stand pipe. The whole assembly is mounted on a flat base.

• Calibration cylinder with spring clamp,Trowel,Tamping rod,Straight edge,Rubber mallet andmeasure. – 1 No. each

Approx. Rs 25,000 / UnitGet Latest Price

• The machine consists of a motorized load frame. The lower platen has two rollers, the distance between which is adjustable. For 150 mm x 150 mm x 700 mm beam, the centre distance between the rollers is 600 mm, while it is 400 mm for beams of size 100 mm x 100 mm x 500 mm. The upper platen has also a pair of rollers whose distance adjustable. It is 200 mm centre to centre, for 150 mm x 150 mm x 700 mm size beam and 133 mm for 100 mm x 100 mm x 500 mm size beam. Total capacity of the machine is 100 KN. 150mm dia pressure gauge of 0-100 KN x 1 KN least count to indicate load is fixed on the load frame. A separate electrically cum hand operated pumping unit housed in a cabinet is supplied. On/Off switch and a slow/fast lever to control rate of loading are fitted on the front panel of the pumping unit. A facility for hand operation is provided. A micro switch and relay fitted inside the pressure gauge protect the unit from over loading.
• Hand operated version consists of a load frame. A small hand pumping unit is attached to the load frame. Since this is a hand operated light weight machine. It is useful for field laboratory also.

• Spare Oil seal
• Hydraulic Oil ( tin of 5 ltrs)
• Beam Mould 10 X 10 X 50 cm
• Beam Mould 15 X 15 X 60 cm
• Beam Mould 15 X 15 X 70 cm
• Beam Mould 15 X 15 X 75 cm
• Trowel
• Concrete Scoop